View SFP-1GBT-09_9024335.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce bel integrated modules 28 turkey court, turkey mill, ashford road maidstone bel me 14 5pp uk +44 1622 757 395 techhelp@belf.com belfuse.com ? 2017 bel power solutions inc. SFP-1GBT-09 v 6 12.16 [1] the bel SFP-1GBT-09 transceiver is an internally co nfigured 1000base-t sfp module with synchronous ethernet capability for gbic host interface. the host interface transmits and receives serial da ta differentially at 1.25gbps. the copper interface is advertised as fu ll duplex and 1000base-t wire speed. key features & benefits ? ?? ? designed with broadcoms bcm54616s chipset ? ?? ? complies with ieee 802.3, 802.3u, and 802.3ab speci fications ? ?? ? configured for operation with a gbic compliant host ? ?? ? supports synce functionality ? ?? ? conforms to multi-source agreement (msa) specificat ions for sfp transceivers (exceptions for synce features) ? ?? ? supports ieee 802.3u and ieee 802.3ab autoCnegotiat ion features to allow networking equipment to automatically dete rmine and adjust the required settings ? ?? ? supports jumbo frames up to 10 kb ? ?? ? operates in extended temperature range of -40 to + 85 c ? ?? ? automatically compensates for baseline wander by re moving dc offset from the input signal ? ?? ? automatic dependent interface (di) crossover, elimi nating the need for crossover cables or cross-wire (mdix) port s ? ?? ? bail latch provides ease of extraction ? ?? ? compact rj45 connector assembly ? ?? ? the bcm54616s physical layer ic (phy) can be access ed via i 2 c interface: phy address = ach eeprom address = a0h ? ?? ? the synce feature can be accessed via i 2 c interface: address = a2h ? ?? ? 128 byte read-only eeprom applications ? ?? ? 10/100/1000 mbps data rate in excess of 100 meters of category 5/5e cable ? ?? ? industrial temperature environments -40 to +85 c ? ?? ? networking equipment ? ?? ? switch-to-switch interface ? ?? ? routers regulatory and standards compliance ? ?? ? compliant with ieee 802.3:2000 ? ?? ? fcc part 15, class a ? ?? ? en55022 class a ? ?? ? ce ? ?? ? e55024 immunity standard and esd
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [2] sfp - 1gbt - 0 9 module specifications parameter symbol min type max units notes supply voltage v dd3 3.13 3.3 3.46 v vdc supply current i s 185 ma 1000 base-t sfp host serial interface (tx/rx) symbol min type max units notes line frequency f line 125 mhz tx output impedance z tx_out 100 differential rx output impedance z rx_in 100 differential clock frequency 25 mhz rise/fall time t r /t f 4 ns 20% - 80% rms phase jitter f j 1.5 ps-rms f j = 12 k hz to 20 mhz offset frequency synce symbol min type max units notes recovered clock jitter 25ppm recovered clock rco 25 mhz (125mhz for locally generated clock) primary reference clock prc 25 mhz 25ppm environmental specifications symbol min type max units notes operating temp t op -40 +85 c case temperature storage temp t stg -40 +85 c ambient temperature
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [3] [1] clock output is disable (by clear rco control f lag in synce control) [2] clock output is enable (by set rco control flag in synce control) and recovered clock is disable (by recovered clock control) [3] clock output is enable (by set rco control flag in synce control) and recovered clock is enable (by recovered clock control) sfp host connector electrical interface descriptions pin name descriptions 1 veet transmitter ground (common with receiver ground) 2 normal operation tx fault not used. internal pull down [1] (default) synce operation rco 125mhz clock locally generated [2] recovered clock [3] : ? link-down C 25 mhz clock locally generated ? 1000base-t C 25 mhz clock recovered from line-side data ? 100base-tx C 25 mhz clock recovered from line-side data ? 10base-t C 2.5 mhz clock recovered from line-side d ata (note: phy configuration also required) 3 tx disable disable phy when logic '1'. internal pull down 4 mod-def2 signal sda (data) of the two-wire serial interface. internal pull up 5 mod-def1 signal scl (clock) of the two-wire serial interface . internal pull up 6 mod-def0 this pin is internally tied to transmit ground 7 normal operation rate select not implemented synce operation prc primary reference clock (25mhz input) (note: phy configuration also required) 8 los logic '1' when no signal or linked at 10base-t (def ault) 9 veer receiver ground (common with transmitter ground) 10 veer receiver ground (common with transmitter ground) 11 veer receiver ground (common with transmitter ground) 12 rd- differential transmitter output. user to terminate 100 differential at host. ac coupled within sfp 13 rd+ differential transmitter output. user to terminate 100 differential at host. ac coupled within sfp 14 veer receiver ground (common with transmitter ground) 15 vccr 3.3v power (common with vcct) 16 vcct 3.3v power (common with vccr) 17 veet transmitter ground (common with receiver ground) 18 td+ differential receiver input. 100 differential term ination & ac coupling within sfp 19 td- differential receiver input. 100 differential term ination & ac coupling within sfp 20 veet transmitter ground (common with receiver ground)
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [4] part number link indicator on rx_los pin auto-negotiation synce host interface duplex mode SFP-1GBT-09 yes enabled disabled gbic full the SFP-1GBT-09 will default to gbic without synce support. in this mode pins 2 and 7 have no function . change configuration users may select various configuration options for the module by writing to a range of i2c addresses w ithin the device. synce control* bit read/write name description 7:3 write only reserved write 1 only 2 write only rco control 0 = enable c lock o utput (pin 2) 1 = disable clock output (pin 2) (default) 1 write only reserved write 1 only 0 write only clock source select 1 = internal 25mhz oscillator (default) 0 = external primary reference clock (pin 7) input * direct access by write configuration byte to i2c device under a2h address. recovered clock control i2c device address control register byte 1 byte 2 description ach ach 17h 15h 0fh 00h 44h 00h disable recovered clock (default) ach ach 17h 15h 0fh 00h 44h 10h enable recovered clock advertise 1000base-t full duplex capability and mas ter / slave configuration i2c device address control register byte 1 byte 2 description ach 09h 02h 00h a utomatic m aster/ s lave configuration (default) ach 09h 1ah 00h configure sfp as master ach 09h 12h 00h configure sfp as slave interface selection at power up, the SFP-1GBT-09 is configured in gbic mode. the user may select sgmii mode by writing the following two bytes to register 1ch. i2c device address control register byte 1 byte 2 description ach 1ch fch feh set mode to gbic (default) ach 1ch fch fch set mode to sgmii default configuration
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [5] list of supported ieee defined phy registers C i2c device address ach register name 00h control 01h status 02h-03h phy identifier 04h auto-negotiation advertisement 05h auto-negotiation link partner ability 06h auto-negotiation expansion 07h next page transmit 08h link partner received next page 09h 1000base-t control 0ah 1000base-t status 0fh extended status phy register 00h: control bit name description r/w default 15 reset software reset 1 = phy reset 0 = normal operation r/w *self-clearing 0 14 loopback internal loopback mode 1 = enable loopback mode 0 = disable loopback mode r/w 0 13 speed selection (lsb) when auto - negotiation is disabled, bits 6 and 13 can be used to manually select the speed of operation bits [6, 13] 11 = reserved 10 = 1000mbps 01 = 100mbps 00 = 10mbps r/w 0 12 auto-negotiation enable if enabled, auto - negotiation result overrides speed selection, duplex mode settings. 1 = enable auto-negotiation process 0 = disable auto-negotiation process r/w 1 11 power down placed sfp in a low - power mode. 1 = power down 0 = normal operation r/w 0 10 isolate 1 = isolate 0 = normal operation r/w 0 9 restart auto-negotiation when auto - negotiation is enabled, setting this bit restarts the auto-negotiation process. 1 = restart auto-negotiation process 0 = normal operation r/w *self-clearing 0 8 duplex mode 1 = full duplex 0 = half duplex r/w 1 7 reserved write as 0, ignore on read r/w 0 6 speed selection (msb) use in conjunction with bit 13 r/w 1 5:0 reserved write as zero, ignore on read r/w 0000 00
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [6] phy register 01h: status bit name description r/w default 15 100base-t4 100base - t4 protocol is not supported. 0 = not capable to perform 100base-t4 ro 0 14 100base-tx full duplex 1 = capable to perform full duplex 100base - tx 0 = not capable to perform full duplex 100base-tx ro 1 13 100base-tx half duplex 1 = capable to perform half duplex 100base - tx 0 = not capable to perform half duplex 100base-tx ro 1 12 10base-t full duplex 1 = capable to operate at 10base - t in full duplex mode 0 = not capable to operate at 10base-t in full dupl ex mode ro 1 11 10base-t half duplex 1 = capable to operate at 10base - t in half duplex mode 0 = not capable to operate at 10base-t in half dupl ex mode ro 1 10 100base-t2 full duplex 100base - t2 protocol is not supported. 0 = not capable to perform full duplex 100base-t2 ro 0 9 100base-t2 half duplex 100base - t2 protocol is not supported. 0 = not capable to perform half duplex 100base-t2 ro 0 8 extended status 1 = extended status information in register 0fh ro 1 7 reserved ignore on read ro 1 6 mf preamble suppression 1 = phy will accept management frames with preamble suppressed 0 = phy will not accept management frames with prea mble suppressed ro 1 5 auto-negotiation complete 1 = auto - negotiation process completed 0 = auto-negotiation process not completed ro 0 4 remote fault 1 = remote fault condition detected 0 = no remote fault condition detected ro 0 3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 2 link status 1 = link is up 0 = link is down ro 0 1 jabber detect 1 = jabber condition detected 0 = no jabber condition detected ro 0 0 extended capability 1 = extended register capabilities 0 = basic register set capabilities only ro 1 phy register 02h-03h: phy identifier bit name description r/w default 15:0 address 02h: phy id (msb) msb of phy identifie r ro 0362h 15:0 address 03h: phy id (lsb) lsb of phy identifier (* - phy rev number) ro 5d1*h phy register 04h: auto-negotiation advertisement bit name description r/w default 15 next page 1 = next page capable 0 = no next page capability r/w 0 14 reserved write as zero, ignore on read r/w 0 13 remote fault 1 = remote fault supported 0 = no remote fault r/w 0 12 reserved write as zero, ignore on read r/w 0 11 asymmetric pause 1 = advertise asymmetric pause 0 = advertise no asymmetric pause r/w 0
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [7] bit name description r/w default 10 pause capable 1 = capable of full duplex pause operation 0 = not capable of pause operation r/w 0 9 100base-t4 capable 100base - t4 protocol is not supported. do not write 1. 0 = not capable to perform 100base-t4 r/w 0 8 100base tx full duplex capable 1 = 100base - tx full duplex capable 0 = not 100base-tx full duplex capable r/w 0 7 100base-tx half duplex capable 1 = 100base - tx half duplex capable 0 = not 100base-tx half duplex capable r/w 0 6 10base-t full duplex capable 1 = 10base - t full duplex capable 0 = not 10base-t full duplex capable r/w 0 5 10base-t half duplex capable 1 = 10base - t half duplex capable 0 = not 10base-t half duplex capable r/w 0 4:0 selector field selector field mode: 00001 = ieee 802.3 r/w 00001 phy register 05h: auto-negotiation link partner abil ity bit name description r/w default 15 next page 1 = link partner capable of next page 0 = link partner not capable of next page ro 0 14 acknowledge 1 = link partner has received link code word 0 = link partner has not received link code word ro 0 13 remote fault 1 = link partner has detected remote fault 0 = link partner has not detected remote fault ro 0 12 reserved write as zero, ignore on read ro 0 11 asymmetric pause 1 = link partner wants asymmetric pause 0 = link partner does not want asymmetric pause ro 0 10 pause capable 1 = link partner is capable of pause operation 0 = link partner is not capable of pause operation ro 0 9 100base-t4 capable 1 = link partner is 100base - t4 capable 0 = link partner is not 100base-t4 capable ro 0 8 100base-tx full duplex capable 1 = link partner is 100base - tx full duplex capable 0 = link partner is not 100base-tx full duplex capa ble ro 0 7 100base-tx half duplex capable 1 = link partner is 100base - tx half duplex capable 0 = link partner is not 100base-tx half duplex capa ble ro 0 6 10base-t full duplex capable 1 = link partner is 10base - t full duplex capable 0 = link partner is not 10base-t full duplex capabl e ro 0 5 10base-t half duplex capable 1 = link partner is 10base - t half duplex capable 0 = link partner is not 10base-t half duplex capabl e ro 0 4:0 protocol selector field link partner protocol selector field ro 00000 phy register 06h: auto-negotiation expansion bit name description r/w default 15:7 reserved write as zero, ignore on read ro 0000 00000 6 receive next page location able 1 = bit 5 determines next page receive location. 0 = bit 5 does not determine next page receive loca tion. ro 1 5 received next page storage location 1 = link partner next pages are stored in register 8 0 = link partner next pages are stored in register 5 ro 1 4 parallel detection fault 1 = a fault has been detected via the parallel detection function 0 = a fault has not been detected via the parallel detection function ro 0 3 link partner next page able 1 = link partner is next page able 0 = link partner is not next page able ro 0
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [8] bit name description r/w default 2 next page able 1 = local device is next page able 0 = local device is not next page able ro 1 1 page received 1 = a new page has been received 0 = a new page has not been received ro 0 0 link partner auto-negotiation able 1 = link partner is auto - negotiation able 0 = link partner is not auto-negotiation able ro 0 phy register 07h: next page transmit bit name description r/w default 15 next page 1 = additional next pages to follow 0 = last next page r/w 0 14 reserved write as zero, ignore on read ro 0 13 message page 1 = message page 0 = unformatted page r/w 1 12 acknowledge 2 1 = complies with message 0 = cannot comply with message r/w 0 11 toggle toggles between exchanges of different ne xt pages ro 0 10:0 message/unformatted code field next page message code or unformatted data r/w 00000000001 phy register 08h: link partner received next page bit name description r/w default 15 next page 1 = additional next pages to follow 0 = last next page ro 0 14 acknowledge 1 = acknowledge 0 = no acknowledge ro 0 13 message page 1 = message page 0 = unformatted page ro 0 12 acknowledge 2 1 = complies with message 0 = cannot comply with message ro 0 11 toggle toggles between exchanges of different next pages ro 0 10:0 message code field next page message code or unformatted data ro 00000000000 phy register 09h: 1000base-t control bit name description r/w default 15:13 test mode bits 000 = normal operation 001 = test mode 1transmit waveform test 010 = test mode 2master transmit jitter test 011 = test mode 3slave transmit jitter test 100 = test mode 4transmitter distortion test 101, 110, 111 = reserved r/w 000 12 master/slave manual config enable 1 = manual master/slave configuration 0 = automatic master/slave configuration r/w 0 11 master/slave config value 1 = configure phy as master 0 = configure phy as slave this bit is ignored if bit 12 = 0. r/w 0 10 port type 1 = indicate the preference to operate as multiport device 0 = indicate the preference to operate as single-po rt device r/w 0
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [9] bit name description r/w default 9 1000base-t full duplex 1 = advertise 1000base - t full duplex capability 0 = advertise no 1000base-t full duplex capability r/w 1 8 1000base-t half duplex 1 = advertise 1000base - t half duplex capability 0 = advertise no 1000base-t half duplex capability r/w 1 7:0 reserved write as 0, ignore on read. r/w 00000000 phy register 0ah: 1000base-t status bit name description r/w default 15 master/slave configuration fault 1 = master/slave configuration fault detected 0 = no master/slave configuration fault detected ro 0 14 master/slave configuration resolution 1 = local transmitter is master 0 = local transmitter is slave ro 0 13 local receiver status 1 = local receiver ok 0 = local receiver not ok ro 0 12 remote receiver status 1 = remote receiver ok 0 = remote receiver not ok ro 0 11 lp 1000t fd 1 = link partner is capable of 1000base - t full duplex 0 = link partner is not capable of 1000base-t full duplex ro 0 10 lp 1000t hd 1 = link partner is capable of 1000base - t half duplex 0 = link partner is not capable of 1000base-t half duplex ro 0 9:8 reserved write as zero, ignore on read ro 00 7:0 idle error count indicate the idle error count, since last read ro *self-clearing 00000000 phy register 0fh: extended status bit name description r/w default 15 1000base-x full duplex 1 = 1000base - x full duplex capable 0 = not 1000base-x full duplex capable ro 0 14 1000base-x half duplex 1 = 1000base - x half duplex capable 0 = not 1000base-x half duplex capable ro 0 13 1000base-t full duplex 1 = 1000base - t full duplex capable 0 = not 1000base-t full duplex capable ro 1 12 1000base-t half duplex 1 = 1000base - t half duplex capable 0 = not 1000base-t half duplex capable ro 1 11:0 reserved write as zero, ignore on read ro 000000000000 eeprom data fields C read only; i2c device address a0h address name of field data value note 00h identifier 03h 01h ext. identifier 04h 02h connector 00h 03h reserved 00h 04h sonet codes 00h 05h sonet codes 00h 06h gbe code 08h 07h fibre code 00h
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [10] address name of field data value note 08h fibre code 00h 09h fibre code 00h 0ah fibre code 00h 0bh encoding 01h 0ch br. normal 0dh 0dh reserved 00h 0eh length 9m-km 00h 0fh length 9m 00h 10h length 50m 00h 11h length 62.5m 00h 12h length copper 64h 13h reserved 00h 14h vendor name 42h ascii: b 15h vendor name 45h ascii: e 16h vendor name 4ch ascii: l 17h vendor name 2dh ascii: - 18h vendor name 46h ascii: f 19h vendor name 55h ascii: u 1ah vendor name 53h ascii: s 1bh vendor name 45h ascii: e 1ch vendor name 20h ascii: space 1dh vendor name 20h ascii: space 1eh vendor name 20h ascii: space 1fh vendor name 20h ascii: space 20h vendor name 20h ascii: space 21h vendor name 20h ascii: space 22h vendor name 20h ascii: space 23h vendor name 20h ascii: space 24h reserved 00h 25h vendor oui 00h 26h vendor oui 00h 27h vendor oui 00h 28h vendor pn 31h ascii: 1 29h vendor pn 47h ascii: g 2ah vendor pn 42h ascii: b 2bh vendor pn 54h ascii: t 2ch vendor pn 2dh ascii: - 2dh vendor pn 53h ascii: s 2eh vendor pn 46h ascii: f 2fh vendor pn 50h ascii: p 30h vendor pn 30h ascii: 0 31h vendor pn 39h ascii: 9 32h vendor pn 20h ascii: space 33h vendor pn 20h ascii: space 34h vendor pn 20h ascii: space 35h vendor pn 20h ascii: space 36h vendor pn 20h ascii: space
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [11] address name of field data value note 37h vendor pn 20h ascii: space 38h vendor rev 41h-5ah 39h vendor rev 20h ascii: space 3ah vendor rev 20h ascii: space 3bh vendor rev 20h ascii: space 3ch laser wavelength 00h 3dh laser wavelength 00h 3eh reserved 00h 3fh cc_base checksum (00h - 3eh) 40h reserved 00h 41h options 12h 42h br. max 00h 43h br. min 00h 44h vendor sn 30h-39h 45h vendor sn 30h-39h 46h vendor sn 30h-39h 47h vendor sn 30h-39h 48h vendor sn 30h-39h 49h vendor sn 30h-39h 4ah vendor sn 30h-39h 4bh vendor sn 30h-39h 4ch vendor sn 30h-39h 4dh vendor sn 30h-39h 4eh vendor sn 30h-39h 4fh vendor sn 30h-39h 50h vendor sn 30h-39h 51h vendor sn 30h-39h 52h vendor sn 30h-39h 53h vendor sn 30h-39h 54h year 31h-32h 55h year 30h-39h 56h week 30h-35h 57h week 30h-39h 58h date code 20h space 59h date code 20h space 5ah date code 20h space 5bh date code 20h space 5ch no diag 00h 5dh enhanced features 00h 5eh no diag 00h 5fh cc_ext checksum (40h - 5eh) 60h-7fh not used 00h
SFP-1GBT-09 sfp copper transceiver, 1000base-t to gbic with syn ce techhelp@belf.com belfuse.com [12] synce configuration enable primary reference 25mhz clock input on pin 7 for the sfp in master mode - synce configuration sequence device address control register / config. byte byte 1 byte 2 description a2h feh - - enable external primary reference clock input (pin 7) ach 09h 1ah 00h advertise 1000base - t full duplex capability and configure sfp as master ach 00h 13h 40h restart auto-negotiation enable recovery clock output on pin 2 for the sfp i n slave mode C synce configuration sequence device address control register / config. byte byte 1 byte 2 description ach ach 17h 15h 0fh 00h 44h 10h enable recovered clock a2h fbh - - enable clock output (pin 2) ach 09h 12h 00h advertise 1000base - t full duplex capability and configure sfp as slave ach 00h 13h 40h restart auto-negotiation mechanical SFP-1GBT-09 synce module master ethernet cable 1000base-t fd 25mhz ext. reference clock 25mhz recovered clock sfp pin 7 rj45 SFP-1GBT-09 synce module slave sfp pin 2 rj45

▲Up To Search▲

Price & Availability of SFP-1GBT-09

	To Download SFP-1GBT-09 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .